Latest Edition: Time saving tactic

[Seascape]

So in my continued effort to roll out fences as quick and easy as possible I just pulled the trigger on this saw.

http://www.milwaukeeconnect.com/webapp/wcs/stores/servlet/product_27_40028_-1_729961_192140_192137

ITS BADASS!!!!!!! NO 2nd PLACE.

This will allow NO CORDS construction of setting posts but more importantly nailing stringers which need the tips trimmed all the way down the line. Coulda went with an 18v however posts would have still been need done with a corded saw............... **** that!

Each time saving feature will add up.

Each tool has been tweaked for ultimate performance from auger all the way to gas power w/ battery assist cordless nail gun.

http://www.milwaukeetool.com/us/en/site.nsf/vwProductAssets/7A79A5A0CEB251BA86256FB200532A5C/$FILE/V28BU.pdf

[Scott]

Nice. I would have to think that Milwaukee tools are #1 especially with the new lithium line. Too bad the housing boom isn't still rocking and rolling because then I be able to afford a few extras.

[Seascape]

Nice. I would have to think that Milwaukee tools are #1 especially with the new lithium line. Too bad the housing boom isn't still rocking and rolling because then I be able to afford a few extras.

Honestly,, theres alot of good tools out. I dont have a problem with any of the big good power tool makers........ they all make good tools. Ryobi and porta cable are not even bad for the money......... but none are even close to this V28 cordless series.

We are estimating it will cut actually 500'+ fence installation on 1 single charge. And do it just like a corded saw.

[Scaper-S2k]

Yes, that's a great saw. It's identical to the Makita I have, except the battery is 28 V. You will like the lithium batteries. Mine charge up VERY fast. I got the whole set for a crazy low price at Home Depot when they had 20% off rechargable tools 2 years ago. The Lithiums were just hitting the market. I also got a recipricating saw for free with mail in UPC.

I went with the smaller batteries because of weight and I read that there wasn't a 'huge' amount of difference between either one except run time of course. But for just working around my house and some other small projects, it's fine because I have 2 batteries.



I'm guessing Milwaukee and Makita are the same company. That saw is exactly like the one I have and both came out with the Lithiums at the same exact time.




I'm not so sure you'll be getting 500' of fencing cut on a single charge. It will depend on the user. If the guy can cut good lines and not bog the saw down, then maybe. I also suppose it will depend on how much cutting you will be doing on that 500' fence.


The blade on mine has lasted a long time also. I'm very pleased with it. I'm hoping you got 2 batteries? Did you look at the kit first? Usually for an extra $80, you can get like 3 extra tools. Kinda strange why they do that. The impact driver will REALLY impress you if you have the chance to get one. I use it more than any other tool. It will drive a lag right through a board and take it out the other side if you wanted!

[Seascape]

Yes, that's a great saw. It's identical to the Makita I have, except the battery is 28 V. You will like the lithium batteries. Mine charge up VERY fast. I got the whole set for a crazy low price at Home Depot when they had 20% off rechargable tools 2 years ago. The Lithiums were just hitting the market. I also got a recipricating saw for free with mail in UPC.

I went with the smaller batteries because of weight and I read that there wasn't a 'huge' amount of difference between either one except run time of course. But for just working around my house and some other small projects, it's fine because I have 2 batteries.



I'm guessing Milwaukee and Makita are the same company. That saw is exactly like the one I have and both came out with the Lithiums at the same exact time.




I'm not so sure you'll be getting 500' of fencing cut on a single charge. It will depend on the user. If the guy can cut good lines and not bog the saw down, then maybe. I also suppose it will depend on how much cutting you will be doing on that 500' fence.


The blade on mine has lasted a long time also. I'm very pleased with it. I'm hoping you got 2 batteries? Did you look at the kit first? Usually for an extra $80, you can get like 3 extra tools. Kinda strange why they do that. The impact driver will REALLY impress you if you have the chance to get one. I use it more than any other tool. It will drive a lag right through a board and take it out the other side if you wanted!

500' of fence consists of about 250 2x4 getting trimmed to fit ,, and about 65 4x4 that maybe 1/3 get trimmed . Fence boards are never trimmed unless its a custom heigth and we cut them in shop.

I think the site says it will cut 171 2x12 cross cuts....... I hope we can do 500'.

I didnt buy the kit ,, but if i like the 28V i may buy a sawzall. Most stuff i am just old school and want a cord? But,,,,, we'll see.

[hardboiled]

What does the saw weigh Mike? I'm wondering how it compares to the Fuego (corded) at 8 lbs.
Erich did that saw of yours see a lot of duty on the siding job? What was your main saw for that, a 12 sliding compound miter?

[Seascape]

7.1 pounds w/o the battery.

[Scaper-S2k]

Seascape, if you haven't used that saw yet, I think you shouyld return it and buy the entire kit. I gaurantee you will want the other tools. And the price difference is crazy low. I guess the recip and circular will cost you around $600 or more? But I think the whole kit is that price or less and you could get a hammer drill and an impact driver drill as well. Possibly even the flashlight.




Hardboiled, Most of my cutting with it was on 2x4's, plywood, 2x12's, and things of that nature.


For the siding I bought a Hitachi 4" saw that is designed for cutting stone, brick, etc. It was priced very good and the smaller diamond blade made it much easier to cut with. It also doesn't need a guard, which really helps out a lot.

[Seascape]

Seascape, if you haven't used that saw yet, I think you shouyld return it and buy the entire kit. I gaurantee you will want the other tools. And the price difference is crazy low. I guess the recip and circular will cost you around $600 or more? But I think the whole kit is that price or less and you could get a hammer drill and an impact driver drill as well. Possibly even the flashlight.




Hardboiled, Most of my cutting with it was on 2x4's, plywood, 2x12's, and things of that nature.


For the siding I bought a Hitachi 4" saw that is designed for cutting stone, brick, etc. It was priced very good and the smaller diamond blade made it much easier to cut with. It also doesn't need a guard, which really helps out a lot.

Man I really dont need another $350 worth of tools sitting around that i rarely use. I'll probally get a sawzall.......... thats it. Hammer drill.... we could use one of those too for removing old stubburn posts on tear outs.

[highlander316]

^ been working w/ a buddy of mine lately putting a drainage system in an old basement. Real narrow channel we have to make along some walls. Hammer drill works great in the tight spots since you can't get a sledge in there.